Hear CO2 flowing? / Gas leak?

You can't leave your homebrew in primary forever! Let's talk about storage.
razorblade
Posts: 34
Joined: 2 years ago
Favourite Beer: Sapporo

Hear CO2 flowing? / Gas leak?

Post #1 by razorblade » 1 year ago

New CO2 tank, new regulator, new lines :)
I can hear the CO2 flowing near the the tank/ regulator area - is this normal?

The nut on the regulator connection to the tank was tightened by hand, and then just a tad with a wrench (it has a plastic gasket in there!) - Should I go more?
I sprayed a lot of soapy water but can't see any unusual bubbling.

Lastly, if I submerge my gas ball lock disconnects in water - they bubble. Is that normal? IS the gas continously flowing even though the disconnect is not connected to anything?
Dave
Posts: 146
Joined: 6 years ago
Favourite Beer: mine

Re: Hear CO2 flowing? / Gas leak?

Post #2 by Dave » 1 year ago

Yes leak at connector for sure. With enough of a leak at connectors, you'll hear flow at the reg.
User avatar
Reignman
Posts: 1633
Joined: 7 years ago
Favourite Beer: Pilsner
Location: Cavan, Ont.

Re: Hear CO2 flowing? / Gas leak?

Post #3 by Reignman » 1 year ago

The regulator will get cold which tells you gas is leaking somewhere.
razorblade
Posts: 34
Joined: 2 years ago
Favourite Beer: Sapporo

Re: Hear CO2 flowing? / Gas leak?

Post #4 by razorblade » 1 year ago

Thanks for your help guys. I looked everywhere, and out of frustration I ended up un-doing and redoing all my connections, and I disassembled and reassembled the ball locks as well. Seems to be holding up now. Lets hope it stays that way!
User avatar
ben58
Posts: 310
Joined: 6 years ago
Favourite Beer: APA

Re: Hear CO2 flowing? / Gas leak?

Post #5 by ben58 » 1 year ago

You can always miz some dish detergent and water together, brush the solution onto any fittings and any foaming will indicate a leak point.
razorblade
Posts: 34
Joined: 2 years ago
Favourite Beer: Sapporo

Re: Hear CO2 flowing? / Gas leak?

Post #6 by razorblade » 1 year ago

I tried that, but didn't see anything unusual. I will do it again before I hook up my kegs, but it seems better for now.
ruf1
Posts: 1311
Joined: 5 years ago
Favourite Beer: lots
Location: vancouver b.c

Re: Hear CO2 flowing? / Gas leak?

Post #7 by ruf1 » 1 year ago

When clamping gas lines i found that heating the end of the tubing in boiling water then slip it on and clamp real tight works best for me.

Never had a leak since using this method.

Good luck..........cheers
razorblade
Posts: 34
Joined: 2 years ago
Favourite Beer: Sapporo

Re: Hear CO2 flowing? / Gas leak?

Post #8 by razorblade » 1 year ago

ruf1 wrote:When clamping gas lines i found that heating the end of the tubing in boiling water then slip it on and clamp real tight works best for me.

Never had a leak since using this method.

Good luck..........cheers



Thats exactly what I did for round 2 :) No issues yet!
ruf1
Posts: 1311
Joined: 5 years ago
Favourite Beer: lots
Location: vancouver b.c

Re: Hear CO2 flowing? / Gas leak?

Post #9 by ruf1 » 1 year ago

Right on!

:cheers:

Return to “Bottling & Kegging”

Who is online

Users browsing this forum: No registered users and 5 guests